Архив тега для: API 598: Valve Inspection & Testing Standard

API 598 is the American Petroleum Institute (API) standard that defines inspection and testing requirements for industrial valves, including:
✔ Pressure tests (shell, seat, backseat)
✔ Leakage criteria (allowable rates)
✔ Test procedures (duration, media, pressure levels)

It applies to gate, globe, check, ball, and butterfly valves used in oil & gas, petrochemical, and other high-pressure industries.

API598 Gate Valve Test,300LB API598 Gate Valve Test

🔹 Key Tests Under API 598

1. Shell Test (Pressure Integrity Test)

• Purpose: Checks valve body & seal strength.

• Test Medium: Water, air, or kerosene (non-shock test).

• Pressure: 1.5x valve’s rated pressure (e.g., Class 300 valve tested at 750 psi).

• Duration: At least 60 seconds for liquid, 30 seconds for gas.

2. Seat Test (Leakage Test)

• Purpose: Ensures sealing performance (no leaks).

• Test Medium: Water, air, or inert gas (nitrogen).

• Pressure: 1.1x rated pressure (e.g., Class 150 valve tested at 165 psi).

• Acceptable Leakage: Depends on valve type (see table below).

3. Backseat Test (Stem Seal Test – for Rising Stem Valves)

• Purpose: Verifies stem sealing when fully open.

• Test Pressure: Same as shell test.

• Leakage Allowed: Нулевая утечка (must be bubble-tight).

4. High-Pressure Gas Test (Optional, for Severe Service)

• Purpose: Extra validation for critical valves (e.g., hydrogen service).

• Test Medium: Nitrogen or helium.

• Pressure: Up to 1.5x rated pressure.

Ball Valves Covered by API 598

🔹 API 598 Leakage Allowance (Max Permitted Leak Rates)

(DN = Nominal Diameter in mm)

🔹 API 598 vs. Other Valve Testing Standards

🔹 When is API 598 Testing Required?

✅ New valve manufacturing (mandatory for API-certified valves)
✅ Repair/refurbishment (after maintenance or re-seating)
✅ Customer-requested validation (for critical applications)

🔹 How to Verify API 598 Compliance?

✔ Check the valve nameplate for API markings.
✔ Request test reports (shell/seat test results).
✔ Look for third-party inspection stamps (e.g., Lloyd’s, DNV).

Final Summary

• API 598 ensures valves can handle rated pressure without leaking.

• Shell test = strength check, seat test = sealing check.

• Ball/plug valves allow minor gas leakage, while gate/globe valves must be bubble-tight.

• API 598 vs. ISO 5208: Valve Testing Standards Compared

  Both standards define valve testing procedures, but they differ in scope, leakage allowances, and global acceptance. Here’s a detailed breakdown:

  ---

  🔹 Key Differences: API 598 vs. ISO 5208

  Feature	API 598 (American Petroleum Institute)	ISO 5208 (International Org. for Standardization)
  Primary Use	Oil & gas, petrochemical, high-pressure	General industrial, water, European markets
  Leakage Classes	No formal classes (fixed pass/fail)	A to G (A = zero leakage, G = highest allowance)
  Test Pressures	Shell: 1.5x rated pressure Seat: 1.1x	Shell: 1.5x Seat: 1.1x (similar)
  Acceptable Leakage	Stricter for gas tests (e.g., ball valves: ≤20 bubbles/min)	More flexible (Class D allows droplets)
  Backseat Test	Required for rising-stem valves	Optional
  Fire Testing	Not included (separate: API 607/6FA)	Not included
  Global Adoption	Dominant in North America, Middle East	Widely used in Europe, Asia

  ---

  🔹 Leakage Rate Comparison

  API 598 (Strict)

  • Ball/Plug Valves (Gas Test): ≤20 bubbles/min (for DN ≤100mm)

  • Gate/Globe Valves: Нулевая утечка (bubble-tight)

  ISO 5208 (Class-Based)

  • Class A: Zero leakage (like API 598)

  • Class D: Allows droplets (common for general-purpose valves)

  • Class G: Highest leakage allowance (e.g., for wastewater valves)

  ---

  🔹 How to Interpret a Valve Test Report

  A typical API 598/ISO 5208 test report includes:

  1. Valve Identification

  • Manufacturer, size, model, serial number

  • Pressure class (e.g., Class 300)

  2. Test Conditions

  • Medium: Water, air, or nitrogen

  • Shell Test Pressure: (e.g., 750 psi for Class 300)

  • Seat Test Pressure: (e.g., 330 psi for Class 300)

  3. Results

  Test Type	Pressure Held	Duration	Leakage Observed	Pass/Fail
  Shell Test	750 psi	60 sec	None	✅ Pass
  Seat Test	330 psi	60 sec	5 bubbles/min	✅ Pass (API 598 allows ≤20)

  4. Certification Marks

  • API Monogram (if API 598 certified)

  • ISO 5208 Class (e.g., “ISO 5208 Class A”)

  ---

  🔹 Which Standard Should You Use?

  • For oil/gas, refineries: API 598 (mandatory in many specs)

  • For water, HVAC, EU projects: ISO 5208 (often Class D)

  • Zero-leakage critical apps: Both allow it (API 598 or ISO Class A)

  ---

  🔹 Need Help Deciding?

  • If your valve test report shows ISO Class D leakage, it may not meet API 598 (which is stricter).

  • For fire-safe valves, you’ll need API 607/6FA in addition to API 598.

  Example Scenario:

  • А шаровой кран passes ISO 5208 Class D (allowing droplets) but fails API 598 (which requires ≤20 bubbles/min for gas tests).

  ---

  Final Advice

  ✔ Check project specs – Many contracts explicitly require API 598.
  ✔ For zero leakage, demand ISO 5208 Class A or API 598 bubble-tight.
  ✔ When in doubt, request both tests for critical valves.

• How to Review a Valve Test Report (Step-by-Step Guide)

  If you have a specific valve test report (API 598, ISO 5208, or other), share the following details, and I’ll help you interpret it:

  ---

  1. Key Details to Check in a Valve Test Report

  🔹 Valve Identification

  • Manufacturer name & valve model

  • Size (e.g., 2″ DN50)

  • Pressure class (e.g., Class 150, PN16)

  • Serial number & date of testing

  🔹 Test Standards Applied

  • Is it API 598, ISO 5208, ASME B16.34, or another standard?

  • If ISO 5208, what leakage class (A, B, C, D, etc.)?

  🔹 Test Parameters

  • Shell test pressure (usually 1.5x rated pressure)

  • Seat test pressure (usually 1.1x rated pressure)

  • Test medium (water, air, nitrogen, etc.)

  • Duration (e.g., 60 sec for shell, 30 sec for seat)

  🔹 Leakage Results

  • Shell test leakage (should be zero for API 598)

  • Seat test leakage (compare against allowed rates)

  • Backseat test (if applicable, must be bubble-tight)

  🔹 Certifications & Inspector Sign-Off

  • API Monogram (if API 598 certified)

  • Third-party inspection stamps (e.g., Lloyd’s, DNV, TÜV)

  • Inspector name & date

  ---

  2. Example Test Report Breakdown

  (You can replace this with your actual report data for analysis)

  Test Type	Pressure (psi)	Duration	Leakage Observed	Requirement	Pass/Fail?
  Shell Test	450 (1.5x Class 300)	60 sec	None	Нулевая утечка	✅ Pass
  Seat Test (Gas)	330 (1.1x Class 300)	30 sec	15 bubbles/min	≤20 bubbles/min (API 598)	✅ Pass
  Backseat Test	450	60 sec	None	Нулевая утечка	✅ Pass

  Conclusion: This valve meets API 598 standards since leakage is within limits.

  ---

  3. Common Red Flags in Test Reports

  ❌ “N/A” or missing tests (e.g., no backseat test for a rising-stem valve)
  ❌ Leakage exceeds limits (e.g., seat test shows 30 bubbles/min when max is 20)
  ❌ No inspector sign-off (uncertified tests are unreliable)
  ❌ Pressure not held for full duration (e.g., test aborted at 45 sec instead of 60 sec)

  ---

  4. How to Share Your Report for Review

  If you have a PDF, image, or data table, provide:

  1. Тип клапана (ball, gate, etc.)

  2. Size & pressure rating

  3. Test standard used (API 598, ISO 5208, etc.)

  4. Leakage results (if any)

  *(Example: “2” SS316 ball valve, Class 150, API 598 test. Seat test showed 25 bubbles/min—is this acceptable?”)*

  ---

  5. Need Immediate Help?

  👉 For API 598: Ensure leakage is within Table 5 limits.
  👉 For ISO 5208: Check if leakage matches the declared class (A-G).
  👉 For fire-safe valves: Verify if API 607/6FA tests were done separately.