Архив тега для: China Double eccentric butterfly Valve supplier

Double eccentric vs. Triple eccentric butterfly valve differences

China Double eccentric butterfly Valve Manufacture,China Double eccentric butterfly Valve supplier,China Double eccentric butterfly Valve factory

Double eccentric and triple eccentric butterfly valves are not the same. Their disc and shaft setups are different. These differences change how well they seal, work, and last. Knowing about these differences is important for people who pick valves for factories because:

• Picking the right size and pressure helps things flow well and keeps the system safe.
• Using the right materials and seals stops leaks and makes the valve last longer.
• Putting the valve in the right way helps control and lowers repair costs.

This information helps people make good choices for valves that work well and last a long time.

Key Takeaways

• Double eccentric valves have two offsets. These help lower seat wear. They also make the valve easier to use. Triple eccentric valves add a third offset. This gives a frictionless, metal-to-metal seal. The seal lasts longer with high pressure and heat.
• Double eccentric valves use soft seals. These work well for normal conditions. They are also easier to fix. Triple eccentric valves use metal seals. These stop leaks in tough places. They also need less fixing.
• Double eccentric valves are good for water, HVAC, and general jobs. They work well with medium pressure. Triple eccentric valves are best for oil, gas, power, and chemical plants. They give strong and leak-free work.
• Picking the right valve depends on pressure, temperature, and fluid type. It also depends on what you need it for. Double eccentric valves are a good choice for most uses. Triple eccentric valves seal better and last longer for important systems.
• Checking valves often and putting them in right helps them last. Triple eccentric valves need less fixing. They also save energy by needing less force to use.

Eccentricity in Butterfly Valves

What Is Eccentricity

Eccentricity in butterfly valves means the valve stem is not in the middle. The stem sits a bit off to the side of the disc and valve body. Engineers do this on purpose when they design the valve. This setup makes the disc more stable when the valve opens or closes.

Single eccentricity happens when the shaft is not lined up with the packing axis. This makes it easier to change the gasket and keeps the gasket in one piece. The disc is attached to the shaft and turns in special bearings that help it move smoothly. O-rings and flat gaskets help seal the valve. The sealing surface is shaped like a cone. When fluid pushes on the disc, it presses against the seat and seals tightly. These valves are tested by rules like EN 12266-1 and ISO 5208. The size and shape must match standards like EN 1092-1, DIN 2501, and EN 558-1. These rules make sure the valve works well and is safe.

Note: The distance of the offset is very important. Engineers pick this distance by looking at how the fluid moves, the pressure, the heat, and what the valve needs to do. This helps the valve work right and seal well.

Why Eccentric Designs Matter

Eccentric designs help butterfly valves last longer and work better. When the stem and disc are offset, the disc does not rub as much on the seat. This makes it easier to open and close the valve. It also means the sealing parts do not wear out as fast.

• Double eccentric butterfly valves have two offsets. One is between the stem and disc center. The other is between the stem and valve body center. This setup means the disc and seat touch less. The seat lasts longer and needs less fixing.
• Triple eccentric butterfly valves add a third offset. This changes the angle of the disc’s sealing surface. The sealing surface becomes oval-shaped. There is no rubbing when the valve moves. The seal is even all around. These valves do not leak, even with metal seats. They work well when the pressure and temperature are high.

Studies show that eccentricity makes valves work better. It lowers the force needed to move the valve and stops parts from wearing out quickly. It also helps the valve seal better and work in tough places. Eccentric butterfly valves are strong, last a long time, and control flow well in many jobs.

Double Eccentric Butterfly Valves

Design and Structure

Double eccentric butterfly valves have two main offsets. The first offset moves the stem away from the disc’s center. The second offset moves the stem away from the valve body’s center. This design makes the disc lift off the seat right away when opening. This means there is less rubbing and less damage to the seal. The butterfly plate is shaped to help flow move easily and lower resistance. Many valves use a shaft pin that is easy to remove. This makes fixing the valve simple and makes it stronger. The table below shows the main design parts and what they do:

Sealing and Performance

Double eccentric valves often use soft seals like EPDM or nitrile. These seals stop leaks very well at first. The double offset design gently presses the seal, so it does not wear out fast. This helps the seal last longer. Over time, soft seals can get weaker and let more water leak. The way the valve is built and the seal type matter a lot for leaks. Double eccentric valves can seal both ways, so they work for flow in both directions. They can handle high pressure and heat. Their small size makes them easy to put in.

Note: The double eccentric design makes it easier to turn the valve. This can make the actuator last longer and use less energy.

Common Applications

Double eccentric butterfly valves are used in many places. Water plants use them to control water flow. Oil and gas companies use them in pipes and systems. Chemical plants like them because they do not rust and are easy to control. Power plants use them for steam and cooling water. Other uses are in HVAC, paper making, medicine, food, and factories. These valves are popular because they work well and last a long time.

Triple Eccentric Butterfly Valves

Design and Structure

Triple eccentric butterfly valves have three special offsets in their design. The first two offsets move the stem away from the disc and valve body centers. The third offset tilts the sealing surface into a cone shape. This shape makes sure the disc only touches the seat at the very end when closing. This stops friction while the valve works. The table below shows the main design differences between double and triple eccentric butterfly valves:

This advanced design helps the valve work well and stay strong, even in tough places.

Sealing and Performance

Triple eccentric butterfly valves use a twisting seal method. The disc and seat only touch at the very end when closing. This stops rubbing and keeps parts from wearing out. Metal-to-metal sealing surfaces, often made from strong alloys, keep leaks from happening. These valves can handle high pressure and heat without leaking. The design lets the valve seal both ways and stops rust from harsh fluids. Operators get these benefits:

• No friction when opening or closing, so the valve lasts longer.
• Lower force needed to turn the valve, so smaller actuators can be used.
• Strong sealing even in very hard conditions, like fires.
• Less fixing is needed because parts do not wear out fast.

Tip: Triple eccentric valves can reach Class VI shutoff, so they do not leak even in hard jobs.

Common Applications

Many industries use triple eccentric butterfly valves because they are tough and seal well. These valves are found in:

• Oil and gas work and refining
• Chemical and petrochemical plants
• Power plants, including steam and boiler systems
• Metal making and new material factories
• Water treatment and energy jobs

People in these fields like that the valve can handle high pressure, heat, and harsh fluids. The triple eccentric design makes the valve last a long time, even if it is used a lot or in rough water. This makes the valve great for important pipes and safety systems where it must always work.

Double Eccentric vs. Triple Eccentric

Comparison Table

Main Differences

Double eccentric and triple eccentric butterfly valves are different in how they are built and how they work. Double eccentric valves have two offsets. This helps the disc move away from the seat fast. It lowers rubbing and helps the seal last longer. Triple eccentric valves have a third offset. This makes a cone-shaped, metal-to-metal seal. The disc does not rub the seat, so it can handle more pressure and heat.

Double eccentric valves often use soft seats. These seats stop leaks very well. Some use metal seats, but these might let a little water leak. These valves work well when the pressure and heat are not too high. Triple eccentric valves use a metal-to-metal seal. This stops all leaks, even when things get very hot or the pressure is high. The special design means there is almost no rubbing, so the valve lasts longer.

Double eccentric valves are used in many places. They work in water plants, HVAC, and factories. They seal well, are easy to fix, and are small. Triple eccentric valves are best for hard jobs, like oil, gas, power, and chemical plants. They can handle strong pressure, high heat, and harsh fluids. This makes them good for places where safety and long life matter most.

Both types of valves need to be checked for leaks and damage. Double eccentric valves are easy to fix and do not need much care. Triple eccentric valves need even less fixing because their seal does not rub. This means fewer repairs and more time between checks.

Tip: Triple eccentric butterfly valves help power plants save energy and money by making flow and pressure better.

Unique Advantages

• Double eccentric butterfly valves:
  1. The leak-free design keeps the disc and seat apart when open, so leaks are less likely.
  2. Special bushings and seals stop rust, so you do not need to fix them often.
  3. You can use them for pumps, air valves, and water tanks.
  4. They are small and light, so putting them in is easy.
  5. They work for water, steam, oil, air, and gas.
• Triple eccentric butterfly valves:
  • Three offsets make a cone-shaped, metal seal that lasts a long time.
  • They stop all leaks, even when the pressure and heat are very high.
  • They need less force to turn and save energy.
  • People pick them for jobs where safety, trust, and long life are very important.

Operators should pick the valve that fits their system’s pressure, heat, and fluid. Double eccentric valves are a good choice for most jobs and cost less. Triple eccentric valves are best when you need the best seal and longest life.

Choosing the Right Valve

Application Factors

Picking the right butterfly valve depends on many things. Engineers look at the fluid type, temperature, pressure, and flow rate. They also check where the valve will be used. The valve material must match the fluid to stop rust and last longer. How well the valve seals and how it opens or closes are important too.

Double eccentric butterfly valves work in heating, cooling, and fire safety. They are used in many factories. These valves can handle more pressure and heat than concentric valves. They work for water, gas, oil, and some rough or harsh fluids. Triple eccentric butterfly valves seal better with a metal seat. They are best for tough jobs with high pressure and heat. These valves are used in oil, gas, chemical, and power plants. The third offset in their design stops leaks and helps the valve last longer, even in hard jobs.

The table below shows how pressure, heat, and fluid type affect which valve to pick:

Tip: Always pick valve materials and seals that match your fluid and temperature for the best results.

Cost and Maintenance

Cost and upkeep matter when picking a valve. Double eccentric butterfly valves cost a medium amount at first. Their design cuts down on rubbing and damage. The elastic seat may need to be checked and changed sometimes. You should check the seals, add oil to moving parts, and test for leaks. These valves do not cost much to keep up because you can change the shaft seals and the coatings last long.

Triple eccentric butterfly valves cost more to buy. Their special design and metal seal mean almost no damage to the seal. This means you do not need to fix them often. You can wait longer between service checks. Over time, the lower need for repairs can make up for the higher price, especially in tough factory jobs.

Note: Buying a triple eccentric valve can save money later if you need it for high-pressure or important jobs.

Selection Tips

Engineers should use good steps to pick the right butterfly valve:

• Check the pipe size and match the valve size to stop leaks and help flow.
• Look at the flow rate and pressure drop using the valve’s Cv to pick the right size.
• Make sure the valve material works with the fluid and temperature.
• Pick double eccentric valves for water, HVAC, and most factory jobs with medium pressure and heat.
• Pick triple eccentric valves for oil, gas, steam, and chemical jobs that need no leaks and strong valves.
• Use small valves for tight spaces and big valves for lots of flow, and think about how to support them.
• Follow rules like API 609, ASME B16.34, and ISO 5211 for sizing and putting in the valve.
• Put the valve in the right way and check it often to make it last and stay safe.
• Look at the maker’s charts and details before you choose.

Tip: For water and most factory jobs, double eccentric valves give good value and work well. For tough, high-pressure, or hot jobs, triple eccentric valves seal best and last longest.

Picking the right valve keeps systems safe and working well. People in factories know that using the right valve for the job stops leaks and saves money. You need to match the valve to the pressure, heat, and what flows inside. This helps avoid problems and keeps things running. Makers say double eccentric valves are good for normal jobs. Triple eccentric valves are best for tough jobs with high pressure.

Часто задаваемые вопросы

What is the main difference between double and triple eccentric butterfly valves?

Double eccentric valves have two offsets. This helps the seat last longer. Triple eccentric valves have a third offset. The third offset makes a cone-shaped seal. This stops friction. It lets the valve work with higher pressure and heat.

Can triple eccentric butterfly valves be used for water supply systems?

Triple eccentric butterfly valves are good for water supply systems. They work well when there is high pressure or heat. Their metal-to-metal seal shuts off flow tightly. The valve lasts a long time, even in tough places.

How often should engineers inspect butterfly valves?

Engineers need to check double eccentric valves often. They should look for leaks and worn seals. Triple eccentric valves do not need as many checks. This is because there is less rubbing and wear. Checking valves helps keep them safe and working.

china triple eccentric butterfly valve supplier,china triple eccentric butterfly valve factory,china triple eccentric butterfly valve manufacture

Which industries prefer triple eccentric butterfly valves?

Some industries like oil and gas use triple eccentric butterfly valves. Chemical plants and power plants also use them. These places need valves that do not leak. They want strong valves that work well in hard jobs.